Hayabusa 2 (Хаябуса-2), Procyon – H-IIA F26 – Танэгасима – 03.12.2014 04:22:04 UTC

Автор Космос-3794, 13.08.2010 10:49:07

« назад - далее »

0 Пользователи и 1 гость просматривают эту тему.

tnt22


tnt22

ЦитироватьHAYABUSA2@JAXA‏ @haya2e_jaxa 16 мин. назад

[PPTD-TM1] May 16 at 11:39 JST: the spacecraft altitude is 60m. This navigation image was received at 11:19 JST.


tnt22

:(  
ЦитироватьHAYABUSA2@JAXA‏ @haya2e_jaxa 3 мин. назад

[PPTD-TM1] The spacecraft descent has been autonomously aborted at an altitude of about 50m. Hayabusa2 is currently rising to the home position. Telemetry from the spacecraft has been confirmed and the spacecraft is normal, but the target marker has not been dropped.

tnt22

ЦитироватьHAYABUSA2@JAXA‏ @haya2e_jaxa 5 ч. назад

[PPTD-TM1] May 17 at 11:00 JST: the spacecraft has returned to the home position. Thank you all for the supportive messages we received during the PPTD-TM1 operation.

tnt22

ЦитироватьJonathan McDowell‏Подлинная учетная запись @planet4589 10 мин. назад

JAXA reports that during the aborted descent on May 15 they got a good image of the SCI crater, but then a glitch in the calculated lidar altitude during a mode switch at 50m triggered the abort and prevented release of the target marker; they will try again next week
Источник --> ~30 мая.

tnt22

http://www.hayabusa2.jaxa.jp/en/topics/20190527e_PPTD-TM1A/
ЦитироватьThe Pinpoint Touchdown – Target Marker 1A (PPTD-TM1A) operation

During the PPTD-TM1 operation between May 14〜16, the spacecraft descended to an altitude of about 50m before autonomously stopping the descent and beginning to rise. This abort by the spacecraft was due to an incorrect distance measurement by the laser altimeter (LIDAR) and meant that the target marker could not be dropped. Despite this, it was possible to image around the artificial crater at low altitude. The name of this next operation is 'PPTD-TM1A', denoting it as the second operation with almost the same plan as PPTD-TM1. PPTD stands for 'Pinpoint Touchdown' while 'TM1' refers to the separation of the first target marker for this touchdown.

In the previous PPTD-TM1 operation, the plan was to descend towards the region SO1 and drop the target marker. In PPTD-TM1A, the target marker will be dropped in area CO1, near area SO1. The location is shown in Figure 1.


[Open in a separate window]
Figure 1: Region near the SCI collision point. This image was captured prior to generating the artificial crater.
(Credit: JAXA, University of Tokyo, Kochi University, Rikkyo University, Nagoya University, Chiba Institute of Technology, Meiji University, University of Aizu, AIST.)

Figure 1 is the same image as shown in previous articles, displaying the surface of the asteroid before the generation of the artificial crater. Figure 2 shows the image taken as the spacecraft rose during the PPTD-TM1 operation. The addition of Figure 2 allowed the area around the artificial crater to be understood more clearly, and the area CO1 to be investigated in more detail. The examination revealed the possibility of a touchdown in area CO1. It was therefore decided to descend towards area CO1 and this time, drop the target marker in this region.


[Open in a separate window]
Figure 2: Surface of the asteroid around the artificial crater imaged during the PPTD-TM1 operation. This is a superposition of two images taken from altitudes of about 0.5km and 0.6km. These images were captured on May 16, 2019 with the Optical Navigation Camera – Telescopic (ONC-T).
(Credit: JAXA, University of Tokyo, Kochi University, Rikkyo University, Nagoya University, Chiba Institute of Technology, Meiji University, University of Aizu, AIST.)


[Open in a separate window (left)] [right]
Back ground images of Figure 2. (Left) From altitudes of about 0.5km. Image time: May 16, 2019, 11:36 JST[cut(on-board time). (Right) From altitudes of about 0.6km. Image time: May 16, 2019, 11:39 JST](on-board time).
(Credit: JAXA, University of Tokyo, Kochi University, Rikkyo University, Nagoya University, Chiba Institute of Technology, Meiji University, University of Aizu, AIST.)

The PPTD-TM1A operation will be performed from May 28〜30, 2019. The plan for the operation is almost the same as for PPTD-TM1. Preparation for the descent will take place on May 28 and the spacecraft will start the descent on May 29 at 12:06 JST (on-board time) at a speed of 0.4 m/s. On the same day at 22:26 JST, the spacecraft speed will be reduced to 0.1 m/s. The descent will continue to reach an altitude of about 35m on May 30 at 11:00 JST, and then to 10m at 11:23 JST, the lowest point. The target marker will be separated just before the lowest altitude is reached. The spacecraft will then soon begin to rise and return to the home position on May 31. The operation schedule is shown in Figure 3. Please be aware that the actual operation times may differ as the times listed here are the planned values.


[Open in a separate window]
Figure 3: Schematic of PPTD-TM1A operation. (Credit: JAXA.)
Note: Times listed may differ from the actual operation.

Figure 4 shows the sequence at low altitude. This is almost the same as for the PPTD-TM1 operation.


[Open in a separate window]
Figure 4: PPTD-TM1A low altitude sequence operation. (Credit: JAXA.)

Hayabusa2 Project
2019.05.27

tnt22

Опубликованы материалы пресс-брифинга 22.05.2019 

Hayabusa2_Press20190522_ver10_en3.pdf - 1.6 MB, 20 стр, 2019-05-27 09:24:55 UTC





tnt22

ЦитироватьHAYABUSA2@JAXA‏ @haya2e_jaxa 5 ч. назад

[PPTD-TM1A] May 29 at 11:18 JST: Gate 1 check. The spacecraft and ground system have been confirmed to be normal. PPTD-TM1A will proceed. The spacecraft has not yet begun its descent.


4 ч. назад

[PPTD-TM1A] May 29 at 12:21 JST. We have confirmed that the spacecraft has begun the descent as scheduled. The current descent speed is 40cm/s.

tnt22

https://ria.ru/20190529/1555072153.html
ЦитироватьЯпонский зонд попытается сегодня повторно сбросить "маяк" на астероид
15:53

МОСКВА – РИА Новости. Зонд "Хаябуса-2" сегодня опустится на поверхность астероида Рюгю и еще раз попытается установить своеобразный "маяк" в окрестностях первого рукотворного кратера, что ему не удалось сделать в середине мая. Об этом сообщает пресс-служба JAXA.
Цитировать"Несмотря на прошлую неудачу, нам удалось получить фотографии окрестностей кратера, уточнить его положение и перенести зону посадки из точки S01 в область C01. Без этих фотографий мы не смогли бы найти безопасную точку для проведения этой операции на столь небольшом расстоянии от места падения бомбы", — заявили участники миссии.
Автоматическую станцию "Хаябуса-2" запустили в космос в декабре 2014 года для изучения и забора проб на астероиде Рюгю. Как надеются ученые, она привезет на Землю первые абсолютно чистые образцы первичной материи Солнечной системы.

Японский аппарат достиг цели в начале июня прошлого года и начал длительную процедуру торможения и сближения с астероидом. Получив первые снимки и данные по устройству поверхности и недр небесного тела, зонд начал готовиться к процедуре по забору грунта.

Первая часть этой задачи - "обстрел" астероида и сбор его обломков – была успешно решена в конце февраля этого года, когда "Хаябуса-2" опустилась в точку L08E1 и выстрелила в нее пятиграммовой танталовой пулей. Ученые назвали эту зону "Таматебако" в честь волшебной шкатулки из сказки про подводный дворец Рюгю.

В первых числах апреля пилоты и научная команда миссии успешно реализовали вторую фазу "бомбардировки" астероида – сброс на его поверхность достаточно увесистой "бомбы", чья масса составляла примерно 15 килограмм. Она содержала в себе 4,5 килограмма октогена и была устроена таким образом, что вся сила взрыва оказалась направлена вниз, в сторону поверхности астероида.

После того, как камеры зонда локализовали новорожденный кратер, руководство миссии приняло решение совершить несколько повторных сближений с поверхностью Рюгю для забора образцов "чистой" материи астероида. Для этого "Хаябуса-2" должна была сбросить специальный светоотражающий маячок, который поможет ему осуществить посадку в кратер в ходе последующего сближения.


© JAXA, University of Tokyo, Kochi University, Rikkyo University, Nagoya University, Chiba Institute of Technology, Meiji University, University of Aizu, AIST
Высококачественная фотография рукотворного кратера (С01) на астероиде Рюгю, полученная зондом "Хаябуса-2"

Эта процедура должна была состояться в середине мая, однако она завершилась неудачно - зонд прервал процедуру сближения еще до сброса маяка и вернулся на высокую орбиту. Как сообщили в JAXA, причиной этого послужили ошибки в работе бортового лазера, оценивавшего расстояние до поверхности Рюгю. Никаких других серьезных проблем они не зафиксировали.

Это фиаско в какой-то степени помогло научной команде "Хаябусы-2" – снимки, полученные в ходе сближения с астероидом, помогли ученым найти удобное место для посадки на его поверхность в непосредственной близости от кратера, о существовании которого они раньше не подозревали.

Как планируют пилоты миссии, зонд сблизится с астероидом и почти коснется этой точки завтра в пять часов утра по Москве. Незадолго до этого он сбросит маячок и получит новые фотографии, которые помогут JAXA выбрать окончательное место для повторной посадки аппарата, что произойдет в первой половине июня.

Для реализации всех этих планов у японского зонда не так много времени. Сейчас Рюгю сближается с Солнцем, и в начале июля, как показывают расчеты пилотов миссии, его поверхность станет слишком горячей для безопасного приземления аппарата. Если "Хаябуса-2" не успеет забрать образцы грунта, то, скорее всего, руководство миссии откажется от этой идеи.

tnt22

ЦитироватьHAYABUSA2@JAXA‏ @haya2e_jaxa 13 мин. назад

[PPTD-TM1A] May 29 at 22:56 JST: Gate 2 check to ensure that the descent of the spacecraft was slowing as planned and that both Hayabusa2 and ground system conditions were normal. The altitude of the spacecraft is about 4500m.

tnt22


tnt22

ЦитироватьHAYABUSA2@JAXA‏ @haya2e_jaxa 1 ч. назад

[PPTD-TM1A] May 30 at 11:02 JST: the spacecraft altitude has reached about 100m.


1 ч. назад

[PPTD-TM1A] (Control room report) The LIDAR altitude has passed 100m and the tension in the control room has grown. At 15 light-minutes away, the spacecraft continues to descent autonomously without our assistance. We have to believe in the spacecraft and watch carefully!

tnt22

ЦитироватьHAYABUSA2@JAXA‏ @haya2e_jaxa 1 ч. назад

[PPTD-TM1A] May 30 at 11:12 JST. The spacecraft altitude is about 50m.


1 ч. назад

[PPTD-TM1A] May 30 at 11:15 JST. The altitude is about 35m and we have confirmed the spacecraft has transitioned to hovering.


1 ч.1 час назад

[PPTD-TM1A] May 30 at 11:15 JST. The spacecraft is hovering steadily.

tnt22

ЦитироватьHAYABUSA2@JAXA‏ @haya2e_jaxa 1 ч. назад

[PPTD-TM1A] This image was received on May 30 at 10:59 JST. The shadow of the spacecraft is clearly visible.




1 ч. назад

[PPTD-TM1A] May 30 at 11:24 JST. We have confirmed that the spacecraft has moved from hovering to starting to descend.

tnt22


tnt22

ЦитироватьHAYABUSA2@JAXA‏ @haya2e_jaxa 59 мин. назад

[PPTD-TM1A] May 30 at 11:34 JST. The spacecraft turned to rise near an altitude of 10m. There is applause in the control room!


36 мин. назад

[PPTD-TM1A] May 30 at 12:00 JST. The spacecraft continues to ascend and the altitude now exceeds 400m.

tnt22

ЦитироватьHAYABUSA2@JAXA‏ @haya2e_jaxa 28 мин. назад

[PPTD-TM1A] May 30 at 12:21 JST: Gate 5 check. Both the spacecraft and ground system were confirmed to be fine. The spacecraft is continuing to rise and the current altitude is about 1000m.